What can you do? dir 300nrub7 password. Short instructions for connecting to Wi-Fi

This instruction will cover all the steps that will help you set up the Wi-Fi router D-Link DIR-300 NRU hardware revision B7 for “ Home Internet Beeline." The recipient will receive the following credentials:

• Preparation before setting up, connecting the router, information about updating the firmware, and what you need to do.
• The most extensive errors that occur when the router is configured.
• Setting up l2tp beeline connection on DIR-300 rev.B7.
• Setting up dartless lines How to set a password for a Wi-Fi connection
• Setting up robots Beeline TV - digital tower IPTV.

The process of setting up the router itself is nothing that any hacker wouldn’t be able to complain about due to the clearly written and well-written instructions. I try to write this myself. Let's go!

Update: if your router has firmware 2.5.11 or 2.15.19 (again, 2.5.x) installed, and the interface is set up similar to the screenshot below, follow these instructions: .

Connecting the router to the computer, preparing for setup, how to flash the router and how to work

Connecting the Wi-Fi router D-Link DIR-300 B7 is not particularly difficult: just connect the Beeline cable to the Internet port on the back side of the router, and connect one of the LAN ports with a cable to a similar connector on your computer or laptops, from which the adjustment will be made. Plus, reduce the life of the router. Before speaking, if you don’t plan to flash the router (proc.), then, in principle, everything from setting up the device can be connected to Wi-Fi - from a tablet or to a phone.

Now about the D-Link DIR-300 B7 firmware: for some other models D-Link routers I recommend updating the router firmware so that these modifications can be carried out correctly without any process. Thus, you can uninstall all settings of the router and go back to the method of updating the firmware, just in case of any problems, such as:

• Often there are fleeting connections, “disconnecting” as it helps to restart the router.
• Low fluidity Internet via Wi-Fi, the router is less likely to be smooth.
• Other problems of unclear origin.

Translation: If you have already tried to configure your DIR-300 B7, but it didn’t work, first reset the router to factory settings. To do this, with the router turned on, press and hold the Reset button on the back side for 10-15 seconds, then release it. It will take another 30 seconds to restart the router from the factory settings.

And last: before setting up, disconnect the Beeline connection on the computer you use to access the Internet. And do not connect remotely - after setup, the router itself will establish the connection and then distribute it via local and drone-free Wi-Fi to all devices. Otherwise, if you do not turn on the connection, you will have power for those who have Internet access on their computer and connect via Wi-Fi, but without access to the Internet. And I’m already tired of answering the question.

Setting up l2tp beeline connection on DIR-300NRU B7

The main step when setting up any drone-free router (Wi-Fi router) is to correctly set up the connection parameters of the new one. What we will do is that our version has DIR-300 B7 and the L2TP connection type, which is approved by Beeline. Come on, let's see.

Launch your favorite browser and enter 192.168.0.1 in the address bar. Once you get there, you will be asked for a login name and password for logging into the D-Link DIR-300 NRU B7 router. The standard values ​​are admin and admin, there and there.

After entering the correct data, you will find the main page router settings. However, we don’t bother with it: at the bottom of the “Admin” section, select the “Advanced settings” option.

On the next page, at the “Merezha” item, click on the “WAN” message, then click the “Add” button, without leaving any connection, as is already on the list. Now you have set up your Internet connection on the page, here you need to enter correct parameters for Beeline provider.

Fill in the trace fields as follows (for those that are not known here, the values ​​cannot be changed because they are not obligatory):

• Connection type- L2TP + Dynamic IP
• I'm a koristuvach- Your login for accessing the Beeline Internet
• Password- Your password for Internet access
• VPN server addresses- tp.internet.beeline.ru

This is everything that needs to be changed. After this we press “Save”. After that, you will find yourself on the page where the carefully created creation in the “Rozirvano” section is displayed. Also, for the right-handed person, the light bulb will light up and the number one will be displayed: if you click on it (and then create a trace), you will be prompted to save the configuration of the device again - click “Save”.

Now just update the current page with the list of connections, since you have not made any payments, and Internet Beeline is disabled on the computer itself, you will see that the connection status has changed from “Broken” to “Connected”, so we required

l2TP Beeline connection is connected and working

Now there's a computer, so let's get started public access to the Internet via local measures If you connect to Wi-Fi from another device, you will also be able to access the Internet. Prote, don’t rush to check it out. The best thing to do first is set up your router and the settings of the drone-free Wi-Fi network.

Setting up Wi-Fi on DIR-300 B7

In order to set up Wi-Fi on the DIR-300 B7, go back to the advanced settings page and in the Wi-Fi item select the Basic settings item.

On this page you can configure the following parameters:

• SSID(name of point Wi-Fi access) - enter bashans I have, English characters. This is why I allow you to display your dartless measure in front of the Soviets. For promotions (and recommended) you can use the same access point in the zone.
• Kraina- Measurement standard. Behind the lining it is installed " Russian Federation", but I recommend changing the USA. All devices do not work or are connected to a point in the Russian Federation region. To the USA, everyone is connected without guilt.

Other parameters can be deleted without changing. Save installation waste. Now, at the Wi-Fi point, press the message “Security Settings”.

• Merezheva authentication- WPA2-PSK
• PSK encryption key- the best password for your droneless Wi-Fi I mean, it is necessary to connect to it. Must consist of at least 8 Latin characters and/or numbers.

Save all adjustments. The router is ready for Vikoristan.

Setting up IPTV Beeline (Digital TV via router)

In order to set up the Beeline TV station on the DIR-300NRU B7, simply go to the main page of the router setup ( Shvidke got better) and click on the IP TV station. At the next step you will be asked to select the port on the router to which you will connect set-top box Beeline. Select the appropriate one and save the settings. Ready.

If you feel like doing something, write comments. If you have requested everything, please write (you will be more than welcome) and share the instructions with social measures- It’s better to let others find out easier.

The extensive ownership of the company D-LINK is well known both in Russia and abroad. Among a wide range of devices, a droneless router stands apart cob vine- D-LINK DIR-300 At a low price, incredible reliability and invincibility technical characteristics becoming the first truly affordable home Wi-Fi router. The model appeared on the table in the distance, so that more is being released. What is the difference between routers of different releases, how to connect and configure them for maximum efficient operation is the topic of our article.

External appearance of the router, technical characteristics

D-LINK DIR-300 – router (router) of the global market, suitable for use in the home or small office. It allows you to connect clients to the Internet either via cable (twisted pair) or via wireless connection (WiFi). With the help of a cable connection, you can connect four computers, and via Wi-Fi any number of clients. However, with a skin-to-skin Wi-Fi client connection, the access speed is reduced. If one client can operate at a speed of 150 Mbit/s, two clients can also operate at a speed of 75 Mbit/s.

The router has been present on the market for more than ten years, during which time three generations (revisions) of this router were released.

DIR-300 revision A

The oldest router from the line has long been taken out of production, although you can buy it on the secondary market. The dartless module to the b/g standard will provide speeds of up to 54 Mbit/s in ideal conditions.

DIR-300A – a veteran of the line of routers

The router's Ethernet ports allow you to organize a local network with high-speed access of up to 100 Mbit/s. And the Internet speed axis for clients of the local network will be almost twice as low: small obligation RAM but a weak processor allows DIR-300 rev. And receive Internet traffic with a speed of no more than 50 Mbit/s. If you are connected to the Internet with a more flexible tariff plan, you can replace your old router with more productivity.

The proprietary gray-hot interface is a hallmark of early models of D-LINK routers

DIR-300NRU revision B1, B3, B5

The abbreviation NRU in the model name means that the droneless module complies with the N standard and can provide theoretical Wi-Fi speed up to 150 Mbit/s. Prefix RU to talk about those that the model is fragmented and vibrated for the market of the region of large SND.

DIR-300NRU B1 - strict modern look and 150 Mbit/s all over

A dual-core processor with a clock frequency of 350 MHz and 32 megabytes of RAM allows you to install alternative firmware on these routers, such as OpenWRT and DD-WRT, which greatly expands the capabilities of the router and improves its stability roboti. The processor speed is sufficient for tariff plans up to 100 Mbit/s.

OpenWRT - software for routers with the widest capabilities

DIR-300NRU revision B7, D1, A1

These router versions are based on a new hardware platform, so alternative firmware cannot be installed on them. The standard security software was completely redesigned: the primary web interface was replaced with a new one, with an interactive client connection map and the ability to change rich settings without resetting the router.

The new D-LINK software allows the user to manipulate alternative firmware

Models B7 and D1 are produced with a vertical frame, and the revision A model has become familiar to you. from the outside looking in in the shape of a black cylinder.

DIR-300NRU A1 - space design and entirely earthly characteristics

DLINK DIR-300A first dartless router, which I added to the maximum 10 rocks to that. Simple and unbreakable, processed, does not falter, for at least 5 years, without glitches and without freezing or losing connection until another, leading Internet provider made it difficult for me to replace my old friend with new router. Once again, the DD-WRT firmware is now a veteran, and he is now working in the ranks, repeating the dartless measures in the village booth. Low liquidity has become the trump card of this router - it does not heat up at all, and can therefore operate reliably in climate-controlled environments, for example, during the summer.

Table: common characteristics of D-LINK DIR-300 routers of different revisions

Video: installing OpenWRT firmware on the D-LINK DIR-300 router

Preparing the router before work

In order for the D-LINK DIR-300 to connect all your devices with a single home network and give each client access to the Internet, you need to go through a few preparation steps. The router is required to connect cables to the provider's network and home computers, and the client's network cards are configured to automatically retrieve the address. After this, you will be able to establish access to the Internet and create a drone-free border.

Connecting the router, preparing for setup

The router connection scheme is simple: the provider cable goes into the Internet socket, the local network computer goes to the LAN1-LAN4 network edge connectors. Smartphones, tablets and other drone-free devices are connected via an additional Wi-Fi network.

gate home measures based on DIR-300NRU

Setting up computer maps for robots with a router

Out of the box, the router has a DHCP server automatically activated - the router itself provides the most appropriate addresses to the connecting computers. Therefore, before setting up the router, you will immediately need to switch to the fact that the adapter of the computer or laptop is set up automatically. boundary addresses.

1. Right-click on the “Start” button and select the “Wireless Connections” item from the user menu.

   Viklik connect the edges from the koristuvach menu

2. In the connection window, select the required adapter and use the right mouse button to open its power.

   The adapter has the power to change TCP/IP parameters.

3. From the list of protocols, select TCP/IP parameters and open them to edit.

   TCP/IP protocol – the main conductor of dartless surveillance

4. Set up the automatic extraction of boundary addresses and DNS server addresses, as shown in the screenshot, and then click OK.

   Automatically retrieve the address inserted

Web interface for modem, setup and access protection

The web interface of the modem, from which most of its configuration is done, is located at the address 192.168.1.1. The owner’s name is admin, and the password for registration is empty, so you don’t need to enter it. Change your access password immediately after cob adjustment modem. This will ensure that your measure is protected from third-party interference.

1. Go to the advanced settings mode.

   Widget settings and status are connected on the main side of the modem

2. In the “System” section, go to the “Administrator Password” option.

   Access to system parameters greetings at the expanded levels

3. Enter the password and press the “Log” button.

   Enter your password and confirm in the field below

Video: setting up routers of the DIR-300 family

Setting up a connection to an Internet provider

The router's web interface allows you to set up Internet connections either automatically (with the help of a setup master) or even manually. Before starting the installation, check that the Internet connection is activated by the service provider. Why try connecting to the Internet without a router by connecting your provider cable to hemezhevy map computer.

Master of broadband Internet connection

For a techically non-prepared brownist, Fіrma D-Link did not do in the program of oblivious Routeri Instruk Click'nConnect, Yaki Vimaga, Coristuvach, go through three ecrani pristies of the PIDKOVCHECHENNET TO PARAREMENT PARAREMARISSYA. The router will determine other connection options automatically, depending on the Internet provider cable that is already connected.

1. Open the web interface by entering the address 192.168.1.1 in your web browser.
2. In the “Merezha” section, go to Click'nConnect.

   All the Pokrokov “Maistries” are launched from the side of Swedish adjustments

3. Check your provider cable connections WAN port router.

   Make sure your provider's cable is connected to the WAN port.

4. Select from the list the type of connection that your Internet provider supports, for example PPPoE.

   Select Internet connection protocol

5. Enter the authorization parameters for the agreement: login, password and VPN server name (which is used for L2TP or PPTP connections). In order to deny access to additional adjustments, move the switch at the lower left corner of the window to the “Report” position.

   Enter the login and password from your agreement with the provider

6. Check the settings in the system window and if there are no errors, press the “Save” button.

   Verify the correct settings and press the “Save” button

If you have heard the sound “Take your hand on pulse” and want to do the adjustment manually, you can do it by switching to the advanced settings mode.

Through the extensions menu, the connection to the Internet provider is configured

Setting up L2TP

L2TP is one of the types of VPN, in which “tunnel” can be installed not only behind the TCP/IP protocol, but also with more protocols low level: ATM, X.25 and Frame Relay. The protocol ensures encrypted traffic, so L2TP connections are used more often in corporate settings, but not for connecting to the Internet for private individuals.

1. Manual connection setup is available from the advanced setup menu

2. Create a new connection with the Internet

3. Enter parameters in the window regional registration: login, password and VPN server address

4. If you have a static connection, enter the IP addresses recognized by the service provider.

5. Press the “Freeze” button.
6. Turning to the window with the connections list, activate the creation of entries as connections for cleaning.

   See creations for active entries

Setting up PPPoE

Connections via the PPPoE protocol are the most widespread among Internet providers, and they are simpler to set up, because the authorization parameters require a login and password.

1. From the advanced settings menu, go to the WAN settings in the Merezha section.

   To connect to the PPPoE protocol, go to WAN connections from the configuration extensions menu

2. Next to the list of side interfaces, click the “Add” button to create a new connection.

   Create a new connection using the “Add” button

3. Enter cloud account parameters in the window: connection type (PPPoE), login and password.

   Set the connection type to PPPoE, and take the login and password for the connection from the agreement with the provider

4. If a digital TV set-top box or smart TV is connected to the router, set the IGMP checkbox to the enabled position.

   Activate options for watching IPTV. Don't forget to assign one of the LAN ports to connect the TV set-top box

5. Press the “Freeze” button.
6. Turning to the window with the connection list, activate the creation of entries as a standard connection.

Setting up PPTP

Setting up a connection to the PPTP protocol is in no way different from setting up L2TP, discussed earlier. This way, two types of connections are supported: with static and dynamic addresses. To authorize, all you need is a login, password and VPN server name. Fuck it, what? Danish species The connection is made by the highly dependent processor of the router. I'm yours tariff plan transfers connections at a speed of 90 Mbit/s and more - you may want to consider buying a new, more productive router.

1. From the advanced settings menu, go to the WAN settings in the Merezha section.

   Manually configured PPTP connection is required from the configuration extensions menu

2. Next to the list of side interfaces, click the “Add” button to create a new connection.

   Create a new connection to access the PPTP protocol

3. Enter cloud account parameters in the window: login, password and VPN server address. If the symbolic server address is not provided by the provider, enter it in the TCP/IP address format.
4. If the secondary connection is a static rather than dynamic IP, enter the DNS server addresses, the edge address, the edge mask and the gateway address.

   If you have a static PPTP connection, enter the IP addresses recognized by the service provider.

5. Press the “Freeze” button.
6. Turning to the window with the connection list, activate the creation of entries as a standard connection.

Setting up a static IP

If you are connected to the Internet with a static IP address, a login and password are not required. In the parameters of the created connection, you enter the address taken from the provider, the access mask and the gateway address, after which the router is ready for work.

Home security and drone-free connection installations

Once the router's connection to the Internet has been established, the wireless network and connections of wired clients that have completed the creation of the home network are no longer allowed to be set up. Never create a drone-free network without password protection, as long as you are locked into MAC addresses. An attacker can easily clone the MAC address and connect to your network.

Wi-Fi configuration (create access point, change password)

Another step after establishing a connection to the provider will be to enable the configuration of a drone-free access point, which will allow you to distribute the Internet on a device with a WIFI module: laptop, tablet, smartphone.

1. Bezdrotov's measure is more beautiful to be adjusted from the menu of expanded options.

2. Click the “Advanced settings” button.
3. Turn the button upside down to the dartless connections in the green (on) position.

   Check that the WI-FI mode is turned down

4. Open the main settings of the droneless connection. Indicate the name of the drone-free lane, the communication channel, and the name of the guest lane. Clients of the guest network will be disconnected from the Internet, but will not be able to connect to the local network.

   Enter your network name and select a news channel

5. Turn to the main screen and open the drone-free security settings. Set the encryption type and password for WIFI access.

   Think of and enter a password to access the drone-free route

6. Turning to the main screen, press the message saving settings in the upper right corner.

When setting up a drone-free network, the password is changed by the router to encrypt the data being transmitted. The more characters the password has, the stronger the encryption, and the greater the impact on the router’s processor. Optimal size key – 8–13 characters.

Port mapping

It is necessary for active users to deny access to the resources of their local network from the Internet. Access to home surveillance folders, images from home IP camera, remote administration Remote programs Administrator or Team Viewer and dozens more required additives. To enable such access, it is necessary to use port forwarding so that the router connects the external port to the internal port. It is difficult to set up port forwarding using an additional function on the web interface of the modem.

1. Open your web browser and go to the router’s web interface at the address 192.168.1.1.

   Add a new rule

2. In the window with the list of port reassignments, click the “Add” button.
3. In the dialog for setting up the port, fill in the following fields:
   
4. Press the “Freeze” button at the bottom right corner of the screen.

Setting up IPTV (digital TV)

IPTV setup allows you to see one of four edge ports for transmission to a new digital video stream. To which port can you connect a media player, Smart-TV or digital TV set-top box.

A few months ago, friends of this family asked for help connecting SmartTV to them home router- DLINK DIR-300. Connections for help "Maistra" IPTV setup", the TV miraculously showed hundreds of repeats digital channels, but we didn’t work with Internet services: youtube, mail, online cinema, weather forecast, they complained about the availability of the Internet connection and didn’t start. The documentation showed that for one-hour transmission of video stream and Internet traffic to the port, it is necessary to configure the Dual Access connection, otherwise the router’s original software did not allow this to work, and flashing the router with alternative firmware The rulers did not want this, so as not to waste the guarantee. And yet the output was found: we connected it to one of the USB ports of the TV Wi-Fi adapter and connected through a new connection to the router’s drone-free network. And through an Ethernet connection there is a digital video stream. The price of food is about 500 rubles, and new router With the support of Dual Access it would be much more expensive.

Local network and DHCP server settings

The router advanced configuration mode allows you to configure the parameters of the dhcp server, local network, and internal interface of the router.

Switching D-Link DIR-300 to repeater mode

The standard software does not support the router switching to repeater mode. If you bought a new, stronger router, and want to use the old DIR-300 to expand the area of ​​the drone-free coverage, you can try installing alternative firmware DD-WRT, in which mode the repeater is adjusted literally by clicking the target.

1. For additional functions of updating (updating) internal software, install the DD-WRT firmware.
2. Select the WAN interface and DHCP server on the Installation tab (Basic Settings section). Enter details Merezhevikh tweaked I repeat. The device must be located in the same space as the main router. Our network will be 192.168.128.0/255.255.255.0, and the gateway will be a machine with the address 192.168.128.5. Vaughn DNS server. For the current Dir-300 repeater, the correct address 192.168.128.2 was selected, as it is not distributed by the DHCP server.

   Enter data on the border address, border mask and gateway

3. Enter the type of drone-free track as “Repeater-location”, and the name of the drone-free track must be entered identical to the track name on the main router. At this point we have a special procedure DizAr_net. Let's save the adjustment again.

   Side to the firmware status – repeater mode is activated

Unfortunately, the DD-WRT firmware does not support the entire line of DLINK DIR-300 models. On the project website you can download update images for revision A1 (the oldest DIR-300) and for version DIR-300NRU revisions B1-B3.

Video: installing DD-WRT firmware on D-LINK DIR-300

Administration D-Link DIR-300

The router is an autonomous device that can be used in the future without any assistance from the owner. If the problems have arisen, then you cannot do without the manipulation of the administrator of the network. You may need to reset the router or reset it to factory settings, and in some cases, update the installed software.

Resetting the router to factory settings

You may need to reset the router to factory settings if the device does not work properly and access to the web interface is difficult. Fortunately, all D-LINK DIR-300 routers can be reset to factory settings.

Updating the internal software (firmware)

Updating the internal software will help remove bugs, increase the speed of the router, and improve the stability of the router.

1. Check the revision of the router, this information is on the sticker located on the bottom of the device.

   

   The manufacturer's website contains firmware files for all revisions of the router

2. From the router's settings screen, select the "Program Update" option from the "System" section.
3. Use the “Look” button to select the path to the firmware file and press the “Update” button.

   Enter the path to the firmware file and begin the update process

4. The router goes through the update procedure, which will take about 10 minutes.

Please carefully select the firmware file. Software security from the router of another revision or more old version During installation, the software may make your device completely useless. This can only be confirmed at the service center.

Resetting the router

The easiest way is to reconnect the router by unplugging the adapter from the socket. If the router is installed in an inaccessible location, you can re-enable it through the web interface.

If you want to avoid frayed cables, avoid connections to one month of work on a computer/laptop, and easily move all computer equipment, you need to add and adjust wifi router. A series of articles about setting up various routers will help you set up a drone-free Wi-Fi network at home without much effort.

This article describes how to set up Wi-Fi on the Dlink Dir-300 NRU B5 router. First, it is necessary to work until the rest. Then you need to adjust the measurement on your computer/laptop on automatically retrieves the IP address from the DNS server. After which you connect via the Dlink web interface (this applies to cases where you closed the web interface after updating the firmware). Entered before the browser (bazhano vikorystuvati Internet Explorer or else Mozilla Firefox) 192.168.0.1 login admin, password admin (for details).
The following is sent to the web interface of the Dlink Dir-300 NRU. Pressing the button “Wi-Fi Master for setting up a dartless range”.

You must check the box next to the first setup window. "Take it away dartless connection», I think things have become clearer :). MBSSID parameter (allows one access point to serve up to four drone-free with different adjustments) that BSSID (tse Physical addresses points (MAC addresses) access for wireless networking.). In households, these functions are rarely used, and the very beginning is tainted, so they are depleted. Onslaught "Dali".

For the upcoming holiday, in a row “Private access point” We do not put a check mark, in the SSID row we write the name of the drone-free line, we select the edge, the channel is set to auto or it is indicated as valid, which means the valid channel is described in the article How to select/change a drone-free channel on a router/router . Dartless mode selectable « 802.11 B/G/N mixed» , so that various devices can connect to Wi-Fi, as in a row “Maximum number of clients” Deleting 0 means that the maximum number of devices can connect to the Dlink Dir-300 NRU; if you enter, for example, the number 5, then the maximum number of devices that can connect to the drone-free network will be no more than 5.

To ensure that all devices, new and old, can easily connect to Wi-Fi, select moderate authentication "WPA-PSK/WPA2-PSK mixed".

In the PSK encryption key row, enter a password that you will need to enter in order to connect to a Wi-Fi network (I recommend using a folding password, at least 8 characters with letters, numbers and special characters). All other settings involve encryption, and I recommend that they be removed.

In the coming days, we are amazed at all the adjustments we have ordered, as everything is indicated correctly and under pressure "Save it" Otherwise we are under pressure "Back" it can be corrected.

Now you need to save the settings on the Dlink Dir-300 NRU, for which you press a button "Save it."

On this Wi-Fi setup On the Dlink Dir-300 NRU router, you can complete it, close the browser window, connect to the Wi-Fi device, and find our network.
Enter the password and access the Internet wirelessly.
After configuring the router, you can proceed to setting up the local network

Daedali will gain more popularity. It’s not surprising, it’s even more amazing manual way for connecting to the Internet and communication various outbuildings, because There is no need for vikoristan wires.

However, while surfing the Wi-Fi network, you shouldn’t forget about its security. If you haven’t yet set up a password for Wi-Fi or it’s too simple, it’s possible that the neighbor’s child has already broken your network for a long time and is profiting from the free Internet to her satisfaction.

Of course, you may be a very good person and there is no harm in it for your dear neighbors, but it’s also not a bad idea that your favorite sites have become terribly attractive.

Since you still want to secure your network, let’s figure out how to set a password for Wi-Fi.

Where to set the password for Wi-Fi?

Router (router) is the most extensive device with limited availability Wi-Fi technology Let's figure out how to set the password on your device yourself.

There are many brands of router manufacturers on the market (D-Link, TP-Link, Zyxel, Asus, etc.) and even more different models of these devices. Therefore, within the framework of this article, we do not consider setting a password for all these models, but we will analyze this procedure using one of the popular D-Link routers DIR-300

Adjustment of most daily dartless routers Open a secondary Internet browser. This can be done on a computer, laptop, tablet, or any other device that connects to the router using additional devices or via dartless link.

You need to follow this procedure on a device connected to the router via cable. On the right, if you are connected via Wi-Fi, if you change the password, you will be disconnected from the network and you will have to enter the settings again.

To enable the necessary settings, you need to enter the IP address of the device in the address bar of your browser. Most vikorists use standard IP addresses, but others can use them to assign their own specific address.

The broadest IP addresses of routers:

• 192.168.0.1
• 192.168.1.1
• 192.168.2.1
• 10.0.0.1
• 10.0.1.1

If you don’t see one of these addresses, you can find out your name in the following ways:

1. Marvel at the router body. Ask your distributors to write the IP address of the router interface on a sticker on the bottom of the device.
2. Read the instructions or the CD included in the kit.
3. Search the Internet for information about your router model.

A possible option is that you have a non-standard IP address installed. In this case, you need to find out this address from the person who set up your router or reset the device to factory settings.

Login from the configured router

Once you have determined which IP address is suitable for your device, enter it in the address term of your browser.

Once the connection to the router has been successful, a window for entering your username and password will appear.

For most routers, the default login name and password is “admin”. It's not the fault of the D-Link DIR-300. So you need to enter this word in the offensive fields and click “Enter” on the message.

If after these actions you were not able to configure the device, then other login data was transferred to your router or this data was changed.

If you do not know the name and password for logging into the device, then there are two options:

1. Once you get the IP address, look at the case, read the instructions, search on the Internet.
2. If the first point does not help, you need to reset the router before standard settings for an additional special button on the device.

Setting a password for Wi-Fi

Once you have reached the router interface, find the “Security settings” item in the “Security settings” section. When configured with other router models, the menus look different, but similar items can be easily found behind keywords wi-fi and security.

On the “Security Settings” page you need to set the following items:

• Merezheva authentication
• PSK encryption key
• WPA encryption

In the “Merge Authentication” field, you need to select which authentication technology will protect your Wi-Fi network. WPA2 is currently the most secure method of authentication for drone-free surveillance. It is therefore recommended to select the same item for nadiynogo zakhistu your wifi.

It is not possible to set before choosing a password. The password must be foldable, consisting of letters in different registers and numbers. It’s important that this is some kind of mindless typing, but not specific words. This combination is more complex than gold, and it’s not easy for you to remember. Write it down somewhere and vikoryst when connecting new devices to the drone-free limit.

The next stage will be the adjustment WPA encryption. To do this, you need to select an encryption algorithm in the WPA encryption field. It is recommended to select AES, because He is one of the most powerful.

After entering all the parameters, click the “Change” button to save the settings. After changing settings, most routers will need to be reset. Then, after all, you will be disconnected from the network, and you will have to enter the password again.

Checking Wi-Fi robots

After resetting your router, you will need to reconnect to all devices and enter a new password.

If there is a problem when connected, then, after all, the old settings for connecting to wifi are saved on the device. To resolve this problem, you need to delete the network from the connect list and find the access points again. Once you appear on the list again, log in and enter a new password.