For a long time now, personal computers cannot be seen without a keyboard and mice, which are the main intermediaries in the computer system. Unfortunately, the bears break up and start acting up often. The computer mouse can be removed and cleaned.

Instructions

Brud and saw best penetrates the ball of the bear, sinking under the roller. The cursor begins to crumble as it collapses, and may not collapse at all. It is very important for him to use a kilim and follow it so that he does not accumulate any alcohol on him.

Connect the manipulator to the PC, or even when the system unit is turned off. The body of the bear can be cleaned with a little hair polish and a small amount of rare mild. Don’t even think about holding the bear under the running water. However, the body itself can be thoroughly rinsed after disassembling the optical (optical) bear. It’s just that mechanical bears also have a microcircuit that can always be removed from the body.

Take a small cross screw and unscrew the small screw that is located in the buried bottom of the manipulator body. The case consists of two parts. There may be a small clamp on the side of the screw. Carefully separate the body without causing any special noise.

If the bear is optical, you need to carefully wipe the red “eye”, so that it glows, in its lower part with some cheesecake, cotton wool or an ear stick. You can also quickly apply a spray can to tight areas. Carefully remove the large microcircuit from the body of the optical mouse and separate the plastic parts into a saw, a saw and a hair (outside). From a bag of bears, remove the bag covered with gum and wash it well or wipe it with alcohol. Give special respect to the tickling of the mouse and its fastenings. Brood can often accumulate there.

For mechanical scraping, it is better not to shave it with a knife or razor, but to take a small plastic scraper. Carefully scrape the brood for help there, where possible.

Having removed the saw and the wood that has stuck, remove the fat from the wrapping parts of the manipulator. You can use soft fabric without lint soaked in alcohol. Also wipe all the fillings of the bowl with alcohol so that the drink does not accumulate further.

Now you can pick up the bear. Place the chip (wheel) back and close the case. Do not overcrowd the wire. Tighten the screw and ensure that the bear is cleaned.

Porada added 7 June 2011 Porada 2: How to clean a mouse When cleaning a mouse, it is important to know that the internal mechanism of both the optical and laser models is a tensile and folding mechanism that interacts with any requirement. slowly and step by step. By following a few simple steps, you can thoroughly clean the bowl of grease and saw without damaging the mechanism itself.

You will need

• penzlik, pilosos, twist.

Instructions

Clean the USB cable of the bear. If the drive for carrying out these procedures was the device being ignored by the computer, it is entirely possible to simply laugh at either the USB input on the mouse or computer. Bring the hose from the vacuum cleaner to the adapter or computer panel, and using a pencil, carefully wind the accumulated saw blades into the adapter. Since there is no need to connect a vacuum cleaner to this procedure, you can blow out the mechanism yourself.

Unscrew the fastening from the back wall of the bear. If some of the buttons on the bear’s body are sticking or not responding, then the problem is all in it itself. Therefore, first we need to dismantle the body and clean the “fillings”. Be careful with screws and bolts that have come loose. The stench often disappears, it’s better to take it away before the procedures in a small bag or simply serve it as a place for cleaning.

Use cotton swabs to clean the empty bear. The main focal points of the purchased product will be visible to you as soon as you understand it. All this shuffling between the buttons, the chairs and the small cracks in the body, which all this hour have been accumulating rubbish in themselves.

For your needs, use a soldering iron. If there is a strong impact or for other reasons resulting from any other contact, you will need to turn it in place. The soldering machine is wonderfully suitable for these needs, since there is nothing else, you can’t spend pennies on it. In most cases it will be cheaper to buy a new mouse.

Don't sit at your PC without making sure your hands are clean. This is not only to ensure comfort during operation, but also to allow your equipment to live longer. Be careful when cleaning the laser bear. The design of the laser in it is, as a rule, tendentious, and the slightest pressure can damage its functionality. Optical and older models are less capable of cleaning. How to clean a bowl - version for each other

The first method transfers the extracted brood from the fermenter without opening its body. First of all, we need to put the “bear” in front of the computer. If it is connected to a USB port, then you can work with a non-woking computer, since the standard of this type of connectors allows hot plugging/plugging of devices. The lens on the back of the mechanical manipulator is retracted. Carefully inspect the part for the presence of powder, powder, and other contaminants. If any particles are present, carefully remove them from the surface of the lens using a cotton swab or soft gel pad. Do this as carefully as possible so as not to damage the tensile part. At the bottom of the brew, as a rule, small, round, humic legs grow, until they are ready to collect. Cleaning these parts is not so important. The smallest stains can be removed with just a toothpick. After you have cleaned the legs of the mechanical manipulator, run the mouse over the surface of the table. You, without a doubt, mean how easy and comfortable it is to collapse. The gaps between the buttons, as well as the tickle of the bear, can be cleaned with the help of a toothpick, a cotton swab or sharpened cheese. In this case, it is important to proceed to this point, as debris may penetrate the inside of the device, and then you will have to remove the housing. The very surface of the mechanical manipulator can be cleaned using soft scrapers or soft gannets. Keep an eye on this so that the vologa does not ruin the middle of the structure. This may lead to the release of the microcontroller, and then you will have to go to the store for a new computer bear. It is recommended to clean the mechanical manipulator at least once a month. If you regularly dine in front of the monitor screen, and also if your children play with a computer bear, you need to watch your browsing more often. Another way to clean a computer bear is to transfer the dirt to the body of the mouse. Many PC owners resort to this method when the mechanical manipulator begins to perform poorly, or simply freeze. Well, it depends on the order of actions:

In order to remove the body of the bear, we need a primary twist. Using another tool, carefully unscrew the screws at the base of the rotor. As a rule, in many mechanical manipulators, one screw is in clear view, and another pair is stored under Teflon feet or under a sticker. After this, carefully open the device. Don’t forget to place all the screws in the right place so that the smell doesn’t get lost during the procedure. Let's start cleaning the insides of the structure. For whom do you need access before paying for the microcontroller? If you find saws, debris, or loose hairs on it, carefully clean them with a cotton swab or soft sponge. Always avoid touching sharp objects, otherwise you risk damaging the microcircuit. Next, you need to check the optical and laser sensor of the device. For this cleaning, use a cotton pad or sticks. If the manipulator wheel requires sanitary cleaning, also wipe its surface with a soft disk. After sanding and sawing, the surface of the computer mouse must be defatted. To do this, soak a cotton pad with alcohol and carefully rub all the parts into the vibrator. After such treatment, saws will not accumulate on the muscles for much longer. The finishing touch will be the assembly of the virobus body. To do this, you need to put back all the removed parts (microcircuit, wheel) and tighten the screws. Regular monitoring of your computer bear will help you to prolong the life of the mechanical manipulator, and also protect yourself from pathogenic bacteria that accumulate on the surface of the mouse.

About an hour after you've added your computer bear to the cob, it's unfortunate that particles of dirt have accumulated under the keys, causing the stink to begin to set in when pressed. Sometimes problems arise and the tickling of the mouse begins to spin around like a rapt, with a constant mass of inconsistencies of the koristuvache.

What is it timid? Run to the store, spend money, buy a new Misha? No way. The most practical way to get rid of problems right away is to clean the “fillings” of the bear.

For this purpose it is necessary to develop advanced skills.

Krok 1. Turn the bear over and unscrew the screw at the bottom of the bear with a small, rounded screw. Carefully separate the upper and lower parts of the “rodent”.

Croc 2 At the bottom of the bowl, carefully remove the yellow board by attaching it to the bottom edge.

Croc 3. Pull out the scroll wheel, remove any hairs that have accumulated, and drink (in the photo there is already a cleaned wheel).

Krok 4. On the upper part of the mouse, unscrew the two screws and carefully pull out the mouse keys without damaging the two springs.

Krok 5. Wipe everything that is possible with a hairy gancher cloth. It is important to clean the area from congestion with a hammer. Turn the wheel back to its place, the same board. On the upper part of the bear, place the springs in a specially grooved groove, and then place the keys in the release position, secure everything with screws. Connect the upper and lower parts of the mouse and the grooves. Tighten the main screw.

Krok 6. Well, what do we expect to come out? I’m ready for a clean bowl, what works like that, nothing new! I’m eager to go to the store! It took a lot of patience and a lot of time to clean the computer mouse.

Did Chi help you?

Today I will recognize How to clean Misha , adje l Every rodent starts acting up early and early. If you don’t have to worry about it, it’s enough to remove and clean the big bear. Whose nothing foldable: it takes a little bit of time, a little cross twist and a bit of gancher.

We see the mouse

We first need to connect the mouse to the computer, just don’t forget to turn on the system unit. We won’t worry about rubbing the rodent’s body - for which a small piece of wool is ideal (you can take a little bit of milk if you need it). It’s hard to move the bear under the stream.

Let's disassemble the case

Please let me know Rose Misha X7 We take the prepared cross screw from behind and tighten the screws on the bottom of the bear. Bears in this series have one screw you'll see, there'll be another one claims under the stickera couple more screws maybeunder Teflon feet(although not on all models). There is a small clamp on the side of the screw. Did you turn it up? Now we carefully separate the body - no great zusil is needed for anyone. Regain respect, as if the cord of the mouse was unraveled - then it may become worse.

This is approximately how you need to tighten the screws of the bear. Just try to mіtsnіshe - not enough?

Clean the “filling” of the mouse

So How to clean Misha? In front of us we pull a large microcircuit from the body. We can carefully see all the brood from behind it, the hair is then swept away. Not at any time don't use your razor! The best solution is to use a small plastic scraper to avoid damaging the microcircuit.

Then we wipe the mouse sensor (optical or laser - it doesn’t matter). What are ear sticks or cheesecakes with cotton for? Although, in my opinion, there is nothing beautiful for the spray bottle in the tight air. Don't forget about the bear's tickle - brood can often accumulate there. If necessary, press the fastening wheel (as it always works, I have already written to the statistics).

All the fat is visible

After cleaning the mouse, you need to remove all the fat from its parts. For whom is it leaking alcohol We soften a lint-free cloth, then wipe the body and all parts of the mouse. Now the drinking will not accumulate for another hour.

Removable body

The building was lost. For this purpose, we place a microcircuit and a rotary wheel in the place of the conductor. Then we tighten the screws and, if necessary, glue the Teflon legs back. That's all! Now you know How to clean Misha.

We turn the microcircuit and wire in place. Now we have no more screws to tighten.

Other statistics:

How to properly clean Misha's computer?

If you have noticed that your computer mouse is working poorly or not working properly, then it is not obligatory to buy a new mouse. The reason for this, most likely, is that she got lost. Cleaning the target will solve this problem.

We first need to determine the type of your target. Turn your bear upside down. If you see a bag, then you have a bag Misha. Whenever you change a lens, you have an optical or laser lens. For skin types, mice have their own cleansing methods.

An optical or laser target does not need to be cleaned as often as a target lens, but the need arises every now and then. If you do not clean its surface, the body will turn black. Well, I would like to clean it once a month with a hairless rag. The lens smears rarely, but if it has been damaged, take a soft cloth or a cotton swab, wet it with alcohol or a method for mitya vikon and carefully wipe the lens.

Kulkov's mouse needs to be cleaned frequently, so it is important that you become familiar with the cleaning procedure. The more the ball smudges, the more important it becomes to move the cursor around the screen. In order to move the cursor from one part of the screen to another, you need to raise and lower the mouse several times, and spend hours cleaning it.

It is not obligatory to disconnect the mouse from the computer during the cleaning hour, but do not forget to close all programs so that it does not get pressed or squeezed. If you still decide to visit Misha, don’t forget to turn on the computer before doing so. Never connect the mouse to the computer during work hours. This can damage the motherboard.

Turn your bag over and you will see the lid covering the bag. There are arrows painted on it. With two fingers, lightly press the lid and twist it in the direction of the arrows. Then cover the bottom of the bowl with your hand and turn it over in the cob position. The bag and the crumb are to blame for falling into your hand. If no one was caught, shake Misha a little.

Dry the bag with a hairy gaiter.

Now marvel at the opening to the day of the mouse. See three rollers. With the help of the haired gancher, carefully remove the bruises from them. Place the bag back near the opening and close the lid.

Is Misha still working badly? Try cleaning it again. Isn’t it working again? Well, there is no choice, I will have to buy a new one.

It is best to regularly clean the surface of the computer mouse, and if the surface is clean, the inside will be cleaner.

If your child is exposed to a lot of people (especially if one of them is sick), it is recommended to disinfect their surfaces before using them.