The computer does not download the Internet cable from the router. How can a computer not bait a router with a tethered cable
I wondered if it could be simpler, lower, connect the router to the computer? Right something vsogo for a couple of hvilin. And sometimes the result may be unsatisfactory, for example, the computer does not download the router, and it is impossible to remove the router parameters in the settings. What to work in such a situation? Tim, who wants to try to solve the problem on his own, gave some simple joys. Ale spochatku kіlka slіv pro possible reasons zboyu.
Why the computer does not boot the router: possible reasons
There are a lot of reasons, you can do it richly, in the form of a banal incorrect connection to installation failures, including the router itself, and in case of damage to the computer (physical failures or software failures of the attachment itself will not be looked at in detail).
However, the main considerations for not allowing the computer to run a WiFi router, depending on the situation, are as follows:
- wrong order;
- incorrect access parameters;
- the presence of drivers in the merging card;
- unsuitable Wi-Fi module;
- the merezha is attached.
How robust is it that the computer does not boot the router with a direct connection?
Let's look at the situation, if the coristuvach tries to connect to the router to connect cob lashing through the cable without intermediary. All cables are correctly connected, but all one is not connected. Well, do not sack the computer router, if you want to try it. What work?
First of all, to be sure that all cables are connected correctly, turn over correctly in the web browser entering the address of the router itself. Most of the addresses are 192.168 with two remaining digits 0.1 or 1.1 (for some non-standard models, other addresses may be blocked).
Addresses for entry can be found on a special plate, as it is stashed on the gate side outbuilding. There is also a login and password, which must be entered when entering the office.
Everything must be entered correctly, but the router is not remembered, it is possible, additionally, the router must be re-wired for additional pressing of the On / Off buttons or Power for 10-15 seconds. However, the best router will turn on the electric lines all over the place, maintaining the same interval. If the computer does not boot the router, you can try resetting the router to factory settings. For this case, there is a small opening in the bottom of the case, in which the Reset button is marked.
Rechecking the correctness of the connection
In times like the front, the effect was not small, so the correctness of the direct order was reversed.
Try inserting a tethered cable into another end of the router, or try a similar one on the computer's tethering card. Even if it doesn’t work, it’s possible that the reason lies in the poor quality of the cable itself. In your mind, just replace yoga and try again to get into the fix.
Diagnostics of the connection and rechecking of Ethernet ports
So the situation, if the computer does not work with the Wi-Fi router, may be due to the breakdown of the ports themselves. As it was already said, select another port or “call” the one before which the connection is being made.
However, the reason may be in the lace adapter. In this way, it has changed, that for the new one, all the necessary drivers are installed in the system (moreover, correctly). If it is attached to a specific dispatcher, it is marked with a yellow icon with a hail sign, the drivers need to be reinstalled. Also, as an option, you can win out of sight I will build a farther re-installation of the system, if the driver will be installed automatically. In case of non-standard possessions, it is necessary to win the original discs, or to indicate the place of roztashuvannya installation file driver on hard drive manually.
In order to obtain more detailed information, it is necessary to carry out diagnostics of the connection. It depends on the distribution of the adapter parameters, which can be found in the menu zdіysnyuvati connection to the border, Roztashovany in the standard "Control Panel". As soon as problems are detected, the system will notify you about their recovery.
Re-verification of attributes in measure
Nareshti, the reason why the computer does not boot the router when dartless connection, It may be set in the settings for attaching a merezhі.
In this situation, it is necessary to connect to the router directly behind an auxiliary cable, enter the wireless mode and remove the SSID broadband charging ensign (for TP-Link models). In other outbuildings, you can have the point of attaching the name of the yard, the installation of just attaching the yard (SSID), or else in any other way. If so, it is necessary to re-vantagage in the way described above. In addition, it would be wrong to start and restart the main computer system (as it seems, you never know).
visnovok
In the majority of cases, methods have been developed and assisted in correcting the situation with connections. Well, even though these solutions did not help, so as not to change the possession, it would be necessary to carry out a flashing of the add-on. It’s problematic to kill it on your own in home minds, it’s better to turn into some kind of something service center. Even so, the result will not be given, it is possible to carry out a new diagnostic of the router, not the subject of obvious faults, but when they are detected, replace the attachments.
But, as practice shows, most often incorrectly entered address and parameters are entered at the entrance to the installation, cable and port breakdowns, the presence of drivers in mesh cards and wireless modules, and also the parameters of the mesh are set. So, if you want one of the suggested methods, it’s better to help.
Often traplyayutsya about those that followed the connection of the router with the computer on mesh cable, nothing is revealed. The computer is not responding to the connection, and do not download the router. The problem is so real, and I want to tell you about the possible causes and solutions.
As a rule, connecting a computer to a router with a tethered cable is as simple as it gets. I have є, according to you, you are sure to get everything right. Sounds, about the connections on the dartless line, there are more problems to blame. Ale, today we’ll talk about the problems with the merging cable.
So, if you connect a mesh cable to the router and the computer, and the computer is supposed to respond to the connection circuit, then we need to know the reason. Before the speech Wi-Fi merezhu Vіd thsgogo router you can do a good job and distribute the Internet. In our mind, he did not stіl respectfully. Hocha, yakscho i bezdrotovy merezha if it doesn’t work, and if the indicators on the router don’t light up, it doesn’t sound like it (especially if only the life indicator is on), then your router just zlamavsya for everything. If you work well, if you sound, then the reason needs to be shuffled in another way.
Why is there no connection between a computer and a router via LAN?
In the first place, I'm happy to verify that you correctly connected the computer to the router. When connected to a tethered cable to a computer (or laptop), it is unlikely that you can have mercy, and when connected to a router, you can (if you want, foldably). On the router, a wired cable from the computer needs to be connected in Zhovty LAN roses. І only in the new. There are usually 4 pieces there.
Z tsim, I think the problems of viniknuti are not to blame.
Even more often, in this situation, the computer itself is to blame, or the laptop. And if it's not a router, I'm afraid to think everything. On the right, in the fact that the images on the computers can be easily and understandably get out of tune. It's better to burn the stench. To change it, just connect a mesh cable to the computer from another router, modem, or from the provider. As, for example, when connected to the Internet directly to the computer, everything works, then the reason needs to be shukat in the cable, otherwise it’s better for everything in the router.
Just like that, the rajah go to the extension manager and marvel at how the map is working. Possibly, є pardons in її robots. In this situation, update the driver. So it goes, turn over the included meshwork.
Pay more attention to the LAN connection indicator, as it should be on your router.
If you know about other possible reasons, through which you can’t connect a computer with a router by cable, then share them in the comments!
The computer may not batchit the router for the following reasons:
1. Poor compression or damaged cable. Replace the cable with a different one or try to get a replacement cable.
2. The problem with the lace card. inverted merezhu card in the "Dispatchers of annexes", they did not turn it on over there.
3.Check the practicality of the router. Find out what works for you wifi router you can use the light bulbs, yak You can also try throwing off the resetting of the router for locking up for the help of the Reset button.
4.Computer connections in WAN sockets. Move the cable to LAN socket.
5.Vidsutnist driver. Find the drivers that came with the add-on or download them from the Internet.
6. Problems in the LAN itself. given the problem You can check it out by purchasing a smart card that fits into the PCI port.
You can change the day for help command line, Enter here the row "ping 192.168.0.1 -t" or "ping 192.168.1.1 -t". Also, some problems are being eliminated, as if just restarting the computer.
Even if nothing that was requested did not help, then it is possible, varto, to bring your router for diagnostics to the nearest service center.
The axis of the video in which is explained how to correctly configure the router for correct operation.