The computer does not load the external hard drive: the reason, how to fix it. The computer doesn't flush the hard drive - that's why! Hard drive does not appear
All the computers are installed so that the system does not drain the hard drive, not only connections such as an additional device, but also the installation of a hard drive, on which the operating system is designed to operate. What can be done and how can such a problem be solved? Next, a number of basic solutions are presented that can help you the most. It’s true, I’ll soon have a chance to find out the cause of the illness.
Why doesn't the system flush the hard drive?
As the most widespread reason for such failures, most of the facists are quick to point out the incorrect connection of the hard drive with cables to the motherboard. However, with proper connection, a situation may arise, if, for example, the system does not install a new hard drive, although it is a good one, the operating system is in full use, drivers are installed, etc.
This problem most often arises from incorrect settings of the BIOS (we will talk about this a little later in the report). The same situation can be avoided due to the presence of software failures, if the device that is connected is assigned to the system of the letter. You may find that the disk may be corrupted, and if the hard drive is used to start the OS, it is possible that valuable records and sectors that need updating may be damaged.
Physical causes and ways to eliminate them
This is true for those who do not want the system to support a SATA hard drive (we take this standard of devices as a butt), primarily from the perspective of physical problems.
Obviously, first of all you should check the correctness of the connection and the strength of the input of the loops in the different outlets. In addition, a major cause of incorrect HDD operation is overheating of the bridge, which is more typical for laptops. In this case, you need to turn on the device and let it cool down.
For stationary units, a possible problem may arise by removing the CMOS battery from the socket by a couple of pins (before resetting the parameters).
It is useful to note that there is a special Clear CMOS jumper on the motherboard, which is usually located near the battery. The jumper needs to be switched to positions 2-3 for about 15 seconds, then turn to output connection 1-2.
Here you must pay attention to the correctness of the Master/Slave connection (this becomes the jumper). A hard drive with an IDE interface is bound by the connection between the Master and all devices, including external hard drives or optical drives, by the Slave. This is the same situation if the system does not load another hard drive. But there are still not all the problems.
The system does not waste the hard drive: adjusting the BIOS
Another reason why it is not recognized lies in the incorrect settings of the parameters of the primary BIOS entry/exit system. As soon as the downloaded system informs you that the system disk is not found and asks you to insert it, it is possible that another device is installed in priority of the download.
In each section, the priority (first) device for this section is to select the HDD itself. If you don’t want to waste your hard drive, go to the hard drive setup section and, in the SATA configuration setup row, turn on the AHCI mode, setting RAID or Standard IDE in the drives.
Disk management section
It is also acceptable that the main hard drive is recognized and the OS is installed without problems. Koristuvach connected another hard drive, otherwise there would be no effect. Why doesn't the system drain the external hard drive? There are no reasons for this, one of which is that the disk is assigned to the wrong letter.
This situation is easy to understand: we go to the computer, where there is a similar partition for disks. All devices will be displayed here, as the stinks are not recognized at the initial stage of attraction or are processed incorrectly. Select the required disk, right-click the submenu and go to the next row to change the letter or the path to the disk. After entering a value, the settings are saved and will not be changed. It’s possible that you’ll have to re-enchant it.
Driver problems
Another very common problem is daily or incorrectly installed drivers that affect the operation of both the one installed on the motherboard and the external hard drive.
If the buyer has a disk with drivers, which must be included with the purchase, there are no problems. Just install (or install) the drivers. Since there is no such disk, you can select a directory that is widely available, or install the program on the Driver Booster installation, which, when scanned, identifies deficiencies, errors, or updates to drivers and automatically integrates them into the system.
Checking the hard drive and backing up the recording
Let's face it, this is an unacceptable situation if the operating system from the hard drive is not affected by software errors or damage to the surface.
At first, you will need some kind of valuable disk (for example, a LiveCD or a system distribution kit), after which you will need to press the “R” key and go to the command line, and then use the command chkdsk c: /f /r to check the disk for defects, and then write the lines Bootrec.exe /FixMbr and Bootrec.exe /FixBoot (this will allow you to correct important entries). If this effect does not work, you will need to overwrite the backup sector using the Bootrec.exe /RebuildBcd command. The problem was actually related to this situation, after restarting the vehicle in normal mode without failures.
In case of mechanical failure, the hard drive will have to be replaced. If you want to be sure that you can restore damaged sectors using the additional HDD Regenerator program to remagnetize the disk, it is important to remember this.
Visnovok
Finally, it is impossible to say that for emergencies, if the system does not make all decisions, it is simply impossible to transfer all situations. However, in all your eyes it becomes more frequent, so depending on the situation, you can use a different method to resolve the problem.
There are no obvious problems here, if the hard drive is not recognized by the system as a result of the virus outbreak (it also becomes infected), and even if the protection of a wireless computer is a priority for any kind of hacker. Also, the power supply was not damaged due to incorrect disk partitioning or formatting. Well, if the hard drive, as it seems, has begun to “spit”, there is simply no other solution other than replacement.
Hard disk (HDD) is a device or the main storage device for information in most PCs. A lot of people are concerned that the computer (laptop) does not have a hard drive. Why bother?
In computer slang it is called a Winchester, and it can be either external or internal. On a device that uses the principle of magnetic recording, not only the user’s information is saved, but the operating system that handles service data.
How can we solve the problem of the “invisibility” of the hard drive? Let's take a step-by-step look at what a hard drive is and how to build it so that your PC can be found.
If there are problems with the hard drive, all recorded information cannot be displayed on the computer. The PC may not run on the hard drive for a variety of reasons. We will try to describe all the causes of malfunctions and the available methods for eliminating them.
All these reasons exist both internal and external to the Winchesters, and “rejoicing” in one way or another will be the same.
Diagnostic visits
If such a problem arises, a diagnosis can be carried out as soon as possible. This is necessary in order to identify any problems. However, the problem may not be with the hard drive, but with the operating system. To be clear, the hard drive is connected to another computer.
If the computer gets busy, it means that the “sick” is not the hard drive, but the operating system. Otherwise, the problem most likely lies in a malfunction of the hard drive itself. In this case, it is best to take the device to the manufacturer for repair or replace it with a new one, since it is under warranty.
In the first case, if the problem is in the operating system, it can be corrected with a manual hand. There are a number of methods on how to earn money independently, without financial expenses.
- 1. While the operating system is booting up, click Del/F2 several times. If everything is gone, you will need to adjust the BIOS.
- 2. Once you have connected the internal hard drive to the computer, screw it into an antistatic device to prevent it from escaping from electrostatic discharge.
- 3. Before any manipulations with the hard drive, please be careful how to connect it.
- 4. Antistatic agent is suitable for the lower part of the hard drive (where it is located).
Main problems and methods
These are problems with hard drives that can be corrected with bare hands. For example, once contacts have been made, it is not obligatory to go to the repair shop.Outgoing contacts
If the contact is made, the computer will not load the hard drive. To resolve the problem, reconnect all cables in the system unit. Be sure to reverse all connections or the problem may resolve.Incorrect BIOS settings
If you set the BIOS (basic input/output system) and do not reboot the hard drive, the problem may be in the system date. If the operating system was damaged, the date could be changed, and your computer would “move” in the past. Reset the system date adjustment by removing the battery on the motherboard for 20-35, and then installing it back.
Since the problem itself was in the default date parameters, the computer designated the hard drive as the physical carrier of information.
This is a different problem, because the devices are obsessed with the correctness of the word. In the BIOS, find Boot and make the HDD a priority device, which will be taken into account first.
Lack of food
If the hard drive hears suspicious sounds and recognizes every hour, then it “reads” again, the problem is due to lack of storage, so the PC periodically does not load the hard drive (HDD). There are two solutions to the problem here: the first is to buy a good life block, the other is to get some kind of device out of curiosity.Device conflict
If two hard drives of the same model are installed on your computer, they may conflict with one another. In this situation I will help you step:- 1. Run diagnostics on both devices to identify malfunctions.
- 2. Connect the hard drive to the operating system.
Bus version
Older versions of OS Windows may not support SATA.The smartest thing to do is upgrade to the new OS version. If for any reason you cannot work, you will need to reinstall the operating system and integrate drivers that are supported by SATA.
There is a problem with the setup of the operating system
Everything is fine with the BIOS, but the operating system does not recognize the devices, which must be configured manually, depending on the capabilities of the OS. Earn like this:Krok first Go to “Control Panel” from the “Start” menu and click on the “Administration” section.
Another shortcut: Press the “Computer connection” button.
Lesson three: Press the button “Cleaning with discs”. Here you can download all the disks connected to the computer. There will be no leakage on one of the devices. Right-click on the nameless device and open “Change Disk Letter” and assign your letter label to it.
After this, it is necessary to re-invent the system.
If all these methods did not help and, as previously, the computer (laptop) did not load the hard drive (HDD), then you most likely need to bring it in for repair. You are unlikely to be able to detect problems with the power of power, but your computer can do a lot of work. And there are also situations when professional help is recommended.
The computer does not have a hard drive because the motherboard does not matter. Correctly installing the motherboard drivers and checking the settings of the boss.for 100 UAH. RUB
Many koristuvachs are willing not to buy a ready-made computer, but to collect it with their own hands. Or equip the existing car with these and other parts. Zokrema - with a hard disk. And here such an unpleasant incident occurs - we bought a new hard drive, connected it, but it does not initialize.
However, this problem sometimes occurs with those disks that have been installed for a long time - usually due to software glitches.
It is clear that in case of any other malfunction, if the computer does not run the hard drive, the best solutions will result in failure. However, you can try a lot of simple manipulations with your hand, since the computer does not waste the hard drive.
We'll try to rename the hard drive right away. To find “My Computer”, click on it with the right mouse button and select the “Manage” menu item. On the left half of the window, select the “Disk Management” menu, select the drive you know, click on the right button and select “Change drive letter.” 
The most popular letters are C and D, if they don’t stink, let’s go ahead and use the English alphabet and try, for example, J. After that, restart your computer.
If you didn’t ask and the disk doesn’t show up on its own, then try installing drivers on the motherboard - maybe that’s the problem. If you are building a computer from scratch, the motherboard will come with a driver disk. We insert it into the disk drive, restart the computer, and at the hour of recovery press F6. 
If you do not have the required disk, you will need to find out the model of the motherboard and download drivers for it. Then write them to disk and create them all yourself.
BIOS does not reset hard drive
If this doesn’t help, and the hard drive still doesn’t show up, you’ll have to make some radical changes and check the BIOS settings. You will immediately have respect for those who are most likely to work in this situation, if you already have evidence of working with computer technology on such a level (even though in this case there will be a chance to earn something different).
In any case, the Bios is complicated, you need to know the approach, and even depending on the version, it looks different. And damage to his work may result in even more unacceptable inheritances.
So anyway, we need to leave before anything else. To do this, when your computer is locked, you need to press F8 (other options: F2 and Delete). The BIOS will open. Next, in the main settings of the operating system, enable the AHCI protocol. 
Finally, if the previous manipulations with the BIOS did not bring the desired result, and after rebooting the hard drive is still not visible, we begin to deal with the material part of the problem - the “fix”. 
It works only if the problem cannot be corrected either through the operating system or through the BIOS.
The cable that connects the motherboard and hard drive can connect to up to one of two connectors. You are instructed to connect the hard drive not to the black socket, but to the blue one. 
Black works less consistently, and the reason why Winchester is known may be with whom.
Manual integration of hard drive drivers
If the mechanical delivery did not help, only one will be lost - manually integrate the SATA driver package with the operating system distribution. Even from the name it becomes clear that this business is not simple. You can earn money in different ways.
Users of existing versions of Windows should try to download the necessary driver packages when updating the operating system.
For Windows XP and Windows Vista users, you can easily use the nLite (for XP) and vLite (for Vista) programs. Similar programs for Windows 7 - the principle of their operation is approximately the same. However, you can’t get by with programs alone—it’s a stinking little process.
The main thing you need to do is to know the required driver package. It’s not good to joke about this here on the official website of the motherboard distributor. This is the safest option. Even if you have inconsistent drivers with any other hardware, you run the risk of exposing your computer to a virus infection.
The easiest way to see the motherboard model is through the “power” menu in “My Computer”. Please also note that you are using Windows XP, and the motherboard from recent models will need drivers for AHCI controllers.
Good morning everyone, dear readers! In this article, I will try to explain why the bios does not drain the hard drive - and I will also identify the ways of such a problem in my article.
This problem, if the hard drive is not recognized by the computer, is the most widespread. This applies to both old and new computers. The same applies to new and old, new and new HDDs.
First of all, it is necessary to find out about the cause of such a problem. From time to time, homeowners can manage everything on their own and enjoy working with Windows and a laptop’s hard drive.
Why doesn't the computer have a hard drive?
This means that there are a number of reasons through which the hard drive is forced to terminate its functions. The following reasons can be mentioned:
- The new sata or ide drive has now been connected;
- There were problems with the cable or wires;
- It is possible that the BIOS is configured incorrectly or everything is fine;
- Weak block of life;
- Low cooling system;
- The Winchester itself is very good.
So, you need to carry out diagnostics, and then solve the problem. Let's say, the unsatisfied koristuvach, in a sing-song manner, has to blame for all sorts of things. Let me help you, and we’ll figure out what and how.
First connection of the hard drive
If you are using Gwent connections for the first time, then, despite everything, the system just didn’t work for you. So, it is physically necessary to be located on the desktop, but it is not displayed in the middle of local disks.
In order to fix this problem, you need to press Win and R on your keyboard, write compmgmt.msc and enter “Ok”.
Find and select “Disk cleaning”.
The window that appears in the middle will show all your connected drives, including your problematic hard drive. As a rule, this is due to an incorrectly assigned letter.
Find the required drive and click on the new one with the right mouse button, and then select “Change the drive letter or go to the drive...”.
A window will appear in which you must click the “Change” button.
Now select the letter and enter “OK”.
Invalid format
For normal disk operation, Windows requires the NTFS format.
So, just like in the instructions, go to “Cleaning with disks” to repeat the first two steps. Then press the right mouse button onto the disk and select “Format”.
Select the file system – NTFS and click “OK”.
BIOS does not reboot the hard drive - adjustment
In some cases, the BIOS may set the wrong priority for storage devices. When you are interested in the computer, press F2 (or Del). Which key must be pressed will be indicated when starting the PC. By pressing the required key, you will go to Bios.
Please note that through the settings of BIOS versions, the names of menu items here and there may vary slightly.
Find the “Boot” tab. Vikorist arrows for keruvannya. In the list of priority devices in the first place (1st Boot Priority/First Boot Device), select your HDD.
Press F10 to save and exit, and then press Y to confirm. After this PC, you will be interested in the device you have installed.
SATA robot mode
Most often, BIOS users have a daily operation mode, combined with an IDE. To make the change, you need to go into the BIOS, select Main, Advanced or Integrated Peripherals and find the settings for SATA Operation, Configure SATA As, or OnChip SATA Type.
Select IDE or Native IDE, press F10 and enter Y.
BIOS does not display the hard drive
If the BIOS cannot recognize your hard drive, then, for everything, it is either incorrectly configured or malfunctioning.
Incorrect settings appear as a result of the operator’s actions, and failures can occur for a variety of reasons. Thus, the food supply begins to fail and ends up infecting the system. About this, you can specify the system date - if it is not accurate, then you will certainly be wrong. To resolve this problem, it is necessary to discard all adjustments.
Find the Clear CMOS jumper on the motherboard.
Change the jumper from contacts 1-2 to 2-3, wait for 20-30 seconds and then turn to the output position. In addition, there is another way. Find the motherboard in the system unit and remove the battery.
Turn it back after 25-30 minutes.
Visnovok
Now you know what to do if the BIOS does not flush your hard drive. I hope you were able to solve your problem, thanks to everyone, and don’t forget to put any food in the comments!
The problem is that if the hard drive is not recognized by the computer, the file is extended. This can be done with a new or already installed external HDD. Before you fix the problem, you need to figure out what caused it. You may be able to correct problems associated with the hard drive yourself - for this you just need to follow the instructions and proceed with caution.
There are a number of situations where the hard drive allows you to cancel its function. It's not just the disk connected to the computer first - one day the main HDD may stop working, making it impossible to maintain the operating system. There may be some reasons why:
- First you connect a new disk;
- Problems with cables and wires;
- Incorrectly configured/broken BIOS;
- Weak living unit or cooling system;
- Physical failure of the hard drive.
In some cases, you may be stuck because the BIOS needs to flush the hard drive, but the system doesn’t. Apparently, an inexperienced physician may have difficulty diagnosing and solving problems. Next, we’ll figure out how to treat the skin of them.
Reason 1: First disk connection
If the user first connects an external or internal hard drive, the system may not work. It is not displayed among other local disks, but is not physically operational. This can be easily corrected and done like this:
How to navigate the utility "Keruvannaya with disks" Don’t waste your time, try alternative programs from third-party vendors. In our other article, we outline below how to format with special add-ons designed for advanced work with HDD. Check out method 1, which looks at the robot with different software.
Reason 2: Incorrect format
The disk does not support the item "Change the drive letter or the path to the drive...". For example, through the lack of reliability of the file system. To work normally in Windows, it must be in the NTFS format.
In this case, it is necessary to reformat it so that it becomes accessible. This method is suitable only because the HDD does not contain information, and the data located on it is not important, so all data will be deleted.
Reason 3: Uninitialized HDD
A new and non-corrosive hard drive may not work immediately when connected. The hard drive itself is not initialized and this process must be done manually.
The disk will be initialized and ready for use.
Reason 4: Damaged connections, contacts or cable
When connecting the external and internal hard drives, show respect. An external HDD may not function through a faulty USB cable. There are no obvious reasons for not working through any of these, so take a similar wire with the same connectors and connect the drive to the computer. The internal hard drive may be causing the problem - the cables are out of order and need to be replaced for the drive to work.
It often helps to initially reconnect the SATA cable to another connector on the motherboard. If they are usually enough, you will need to connect the SATA cable to another valid port.
Due to carelessness or insufficient evidence, the user may incorrectly connect the hard drive to the middle of the system unit. Turn over the connections and reconnect so that the contacts do not come out.
Reason 5: Incorrect BIOS settings
The computer does not flush the system disk
It is possible that the BIOS does not have robotic mode installed, but it is not possible with the IDE.
BIOS does not reset hard drive
If the BIOS does not recognize the hard drive, then the reason for this is incorrect configuration or failure. Incorrect settings appear as a result of the operator's actions, and failures can occur for a variety of reasons, starting with interruptions in living viruses and ending with viruses in the system. About this you can check the system date - since it is not accurate, it is a direct indication of a malfunction. For this purpose, you will need to reset it and return it to the factory settings.
Old BIOS
When you try to connect a new drive to an old computer with the same BIOS, you sometimes encounter problems. This is explained by software nonsense and out-of-date control files. You can update the BIOS firmware manually, and then check the visibility of the HDD.
Respect! This is the method of appointments Vinyatkovo for additional confirmation of koristuvachs. You complete the entire process at your own risk; if you do it incorrectly, you can waste your PC’s productivity and waste a lot of time on upgrading its functionality.
Reason 6: Lack of life and cooling
Listen to the sounds that come from the system unit. If you can barely hear the sounds of cycles changing, it’s more likely that the culprit is a weak life block. Work behind the furniture: replace the living block with a stronger one or turn off another device.
If the cooling system does not work well enough, an overheated disk may periodically stop being recognized by the system. This is most often the case when you are using a laptop that has weak coolers and cannot cope with its duties properly. The biggest problem is obvious - the application of intense cooling.
Reason 7: Physical failure
For a variety of reasons, the hard drive can go wrong: coward, fall, blow, etc. If other methods did not help, then try connecting the HDD to another computer. If the fault is not identified by him, then, most likely, it will no longer be possible to fix it on the software level, and you will have to find a service center for repair.
We looked at the main reasons why the hard drive does not start. In reality, there may be more of them, as long as everything depends on the specific situation and configuration. If your problem has not been resolved, please leave a comment and we will try to help you.