I like ttk-chita. I like ttk-cheat Wifi router dir 300 firmware

D-Link DIR-300 routers of different revisions in the latest firmware versions 2.5.11, 2.5.12 and 2.5.19, depending on the model, have got a new web interface. Despite the fact that setting up the router here is done in almost the same way as in previous versions of the interface, it confuses some people, and there are no instructions for the new firmware. (Instructions for configuring the same router with previous firmware versions are available in the D-Link section on this website).

In this manual, step by step on how to configure the DIR-300 wireless router with the new firmware version, set a password for Wi-Fi, and configure IPTV. Shown setting for Beeline and Rostelecom (should be suitable for other providers using PPPoE connection).

How to connect a router

First of all, you need to connect a router for configuration. It is simple to do this: connect the Internet cable to the "Internet" port, and use the supplied network cable by connecting one of its ends to the computer's network card, and the other to one of the LAN connectors on the D-Link DIR-300.

Plug the router into a power outlet, wait for a while until it boots, then in any browser in the address bar, enter 192.168.0.1 in order to enter the settings web interface. You will see a login and password request, by default login and password are admin and admin, respectively. If necessary, switch the settings interface to Russian.

If you cannot enter the router settings, then.

If the login and password do not fit when entering the router settings, try it.

Configuring DIR-300 with new firmware for Beeline

Let's start by setting up a Beeline connection. First of all, if you have such an Internet connection running on your computer (that is, on the computer itself you run the Beeline home Internet), then disable it in the future, after setting it up, do not start it: the connection to the Internet will be established by the router itself, and you there will be Internet access over the local network.

To configure the L2TP Beeline connection on the DIR-300 with firmware 2.5.11, 2.5.12 and 2.5.19, go to the "Network" - "WAN" section, select the Dynamic IP connection already there and click "Delete".

After deleting, click the "Add" button, then set the following parameters for the connection:

• Connection type - L2TP + Dynamic IP
• Interface - Internet
• Name - any
• Username - your login from the Internet Beeline.
• Password and password confirmation - password from the Internet Beeline.
• VPN server address - l2tp.internet.beeline.ru

All other parameters can be left unchanged. If you have any doubts about their correctness, check the screenshot below.

After the settings are made, save the connection and be sure to click on the notification "Device configuration has been changed" and click "Save" to save the settings.

If everything was done correctly, and the Beeline connection on the computer was disconnected, then after a short time in the Network - WAN section you can see that the newly created L2TP connection has a status of "Connected", which means that the connection setup is complete and the Internet is already available from this computer ...

Further steps for setting up a password for Wi-Fi are described immediately after the section on setting up an Internet connection for Rostelecom.

Configuring the DIR-300 Rostelecom router

(the same settings should be suitable for other providers using PPPoE, for example, Dom.ru, TTK in some regions

In order to configure a high-speed Internet connection Rostelecom (PPPoE) on the DIR-300 in the new firmware, first of all, disconnect (if it is connected) this connection on the computer and do not connect in the future - after setting up the router, it will install it by itself, actions on a computer is not needed for this (the Internet will be like a local network) and can cause problems.

In the router settings, go to the Network - WAN section, select the existing Dynamic IP connection there and delete it. Then click "Add" and set the following connection parameters:

• Connection type - PPPoE
• Interface - Internet
• Any name.
• Username - your login for the Internet Rostelecom.
• Password and Password Confirmation is your Internet password.

The other parameters do not need to be changed. Click "Apply", and then click on the notification that the device configuration has been changed and click the "Save" button (this is mandatory, otherwise the settings will be reset on reboot).

On this, the Internet is configured on the router, you can check the status of the created connection to the Network - WAN or in "Status". If the connection is successfully established, then the Internet is already available.

The next step is to configure the Wi-Fi settings.

Wi-Fi setup, password for a wireless network

To configure the wireless network settings, go to the "Wi-Fi" section. The two items that interest us are "Basic Settings" and "Security Settings".

In the "Basic settings" you can set the name of the Wi-Fi access point instead of the standard "DIR-300" (ie the name of the network to which you will connect). This is done in the SSID field.

Do not use Cyrillic for the network name, as this does not always work (for example, some devices may not connect).

After that, go to Wi-Fi security settings and set the following parameters.

If you need DIR-300 firmware, here you will find all the information you need. There are a few things to note:

• If you have a power cut during the flashing, then there is a chance to break the router. So first, make sure you have stable electricity and working power cables. It is possible to connect D-link DIR 300 via UPS for the duration of the firmware.
• Updating the firmware yourself will void your warranty.

Why might an update be needed? Sometimes you don't even need an update, but reinstall an existing firmware version. Causes:

• The Internet is slow and buggy.
• New functions are required, which appeared in the new software version.

Firmware is like a driver or operating system for a router. Firmware written to the permanent memory of the device. First you need to download it.

Brief instruction

In short, the very essence of how to reflash:

• Download the firmware for the D-link DIR 300 from ftp.dlink.ru.
• Go to the router page 192.168.1.1 (or 192.168.0.1).
• Head to the Maintenance section, then Firmware Update.
• Select the firmware file, click "Upload".
• Wait 2 minutes while the router installs the firmware. All.

Now everything is the same, but in more detail.

Download firmware

• It weighs only a few megabytes. In the address bar, write the address dlink.ru, then go to the official website of the router developer, this is ftp with firmware.
• In a folder called pub, find the Router section.



• After that, find the folder with the firmware for your model and revision of the router, in our example it is DIR-300_NRU.



• Next, head to the Firmware folder.




• Now you need to find out the revision of the DIR router. You need to take your router, turn it over, and see what is written on the sticker on the bottom side.
• In this case it's B1, you might have A1 / B1 / C1 / D1 / B3 / B5 / B7 / B6.



• Having opened the folder on ftp called Firmware, select the partition that corresponds to your model of the DIR300 router.



• Download the firmware. It is a small file with a bin extension.

Connecting the router to a PC

Connect D-link to your computer via patch cord. Can be flashed from regular stationary PCs, laptops and netbooks. Turn on your router. You need to check your network setup.



• In Win7 go to "Start", then to "Control Panel", then "View network status and tasks."
• Find the link "Changes to adapter parameters" in the left menu. Find the icon for connecting by local. network, go to the connection properties.
• A window will open, select there protocol version 4 (TCP / IPv4) and click the "Properties" button.



• On the "General" tab, see if the settings are set: "Obtain an IP address automatically" and "Obtain DNS server address automatically".

Now directly to the firmware update.

Flashing




• Open your browser, write 192.168.1.1 instead of the site address, you will go to the page generated by the router.
• Enter your username and password to access the DIR 300 settings. If you did not set a password, then just write admin.
• On the router's page, you can find out the revision version (marked with a light green arrow at the top), this is necessary in case your sticker on the bottom of the router is worn or peeled off.
• Go to the "Maintenance" section, then to "Firmware Update. Then go down to "Firmware upgrade", then "Select file".
• Find the downloaded official firmware from D-link on your computer. Then click “Upload”.



• The firmware update of the router will start, it will take exactly 2 minutes. Do not unplug the router at this time, otherwise it may cause damage.




• When the update is over, you will be redirected to the login and password window.
• Look at the top line, if you updated the firmware to a new version, then there should be changes. If you just flashed (by analogy, like reinstalling Windows), then the same firmware version number will be waiting for you.

When the firmware of the DIR-300 router is reinstalled, the Internet settings do not change. You can continue using your computer immediately.

D-Link DIR-300 C1 model firmware




• To flash the D-Link DIR-300 C1 router, you need to download the firmware file (.bin) from here.




• After that download the zip archive from here.




• Make sure your router is connected to your computer (laptop or netbook) with a cable connection and not over Wi-Fi.
• Unpack the downloaded zip archive on your computer and run the dcc.exe program.
• D-Link Click'n'Connect will then start. In it, select "Connect and configure the device."

Update the software, it's easy - the tips will help. As a result, not the last, but working firmware for this model will be installed. If you are satisfied with the operation of the router, then you can not continue.

Updating D-Link DIR-300 C1 to the latest version

But if you want to update D-Link DIR-300 C1 software to the latest firmware version, then ...

• Go to the router settings, find the "System" section, then "Software Update".
• There, select the bin-file of the firmware (we downloaded it earlier).
• Then click "Update" - wait for the standard 2 minutes for the update.

Error messages or router hangs may appear, then do not turn off the power, but wait another 5-10 minutes for the installation to complete correctly.

DIR 300 N150 revision D1

Flashing the DIR 300 N150 D1 using the example of firmware version 2.5.4 with the new Air web interface.




• Go to the settings in the usual way, you will see the "Home / Information" page, where you can see the exact model name and firmware version.



• To install a new or reinstall an old firmware, click on its version, the "System / Firmware update" page will open.
• Use the "Browse" button to select the update file (previously downloaded from here).
• Click Update. Waiting 2 minutes.




This is what the firmware file looks like on the manufacturer's ftp server

Restore settings

If you have failed to flash DIR-300, you can restore the factory settings of the router.

• The simplest thing is to use the RESET button on the router case; you need a toothpick, since the button is recessed into the case. Press it for 10 seconds, release, after that the router will reboot and start with zero settings.
• You can also use the corresponding item in the web interface settings menu.

You have learned how to install the official firmware on a DIR 300 router (revisions A1 / B1 / C1 / D1 / B3 / B5 / B7 / B6). Also on our website you can read how to set up the Internet on the D-link DIR 300 router.

Over time, technology becomes obsolete, and some devices are replaced by others - new and more efficient. The same is true for wireless software. What to do with a normally functioning router but with outdated firmware, do not throw it away? This article discusses the firmware of the D-link DIR 300 router.

Before proceeding with further actions, you need to understand that flashing the router carries a certain amount of risk. Sometimes it can lead to a complete inoperability of the device. Therefore, you need to update the router's firmware when there is a need for it. If your router is constantly buggy or slow, a firmware update can bring it back online.

Attention: updating the firmware of a router, the warranty period of which has not yet expired, will void the manufacturer's warranty.

Another important point: there should be no electricity problems during the firmware update process. For those of you who constantly lose light, we strongly recommend connecting the router to the mains through.

Firmware - firmware stored in the CMOS of the computer. It is also used in phones, tablets, routers and other devices. In other words, it is a certain version of the operating system, and the process of updating it is called a flashing.

First you need to download the D-link DIR 300 firmware.

In the address bar of your browser, type ftp.dlink.ru and go to the site with the firmware. Go to the pub folder, then to the Router section.

Among the entire list of routers, find and open the DIR-300_NRU folder.

Go to the Firmware section.

Be careful in the next step. It is necessary to select the correct revision of the router model. To do this, turn the modem over and on the bottom panel look at the contents of the barcode sticker, the revision should be indicated here. In our case B1, you might have B2 - B7.

After opening the Firmware folder, select the partition corresponding to your router.

Download the file with the bin extension.

What to do next? Connect the router to your computer and turn on the power. Then check your LAN settings. In Windows 7 go to "Start" - "Control Panel" - "View Network Status and Tasks" - left menu "Change adapter settings".

Select the local area connection shortcut, right click on it and open Properties. In the window that opens, select protocol version 4 (TCP / IPv4) and click "Properties" again.

On the General tab, make sure the Obtain an IP address automatically and Obtain DNS server address automatically are selected.

If you have forgotten the password for entering the settings, in one of the previous articles it was told,?

Pay attention to the top line, here is the revision version that we looked at on the sticker of the modem.

If, for any of the reasons: the sticker is peeled off or the letters are erased, you could not find out the revision of your device, now this can be done in the login and password entry window.

In the login and password field, enter admin, if other values \u200b\u200bwere set for user authentication, write your data.

In the settings interface that opens, go to the "System" - "Software update" section.

In the appropriate window, specify the path to the firmware file with the bin extension on the computer. At the beginning of the section about updating the D-Link DIR-300 C1 firmware, it was already mentioned.

Click the "Update" button to install the software - it will take up to 2 minutes.

Sometimes, during the firmware of the router, error messages may be displayed or the browser freezes. In this case, do not take any action, but wait 5 - 10 minutes, the firmware should complete correctly.

Firmware update DIR 300 N150 revision D1

There are several versions of D-Link DIR 300 routers on the market with different firmware revisions and different appearance of web interfaces.

Consider updating the software of the DIR 300 N150 router with revision D1 using the example of firmware 2.5.4 with the new web interface "Air".

After entering the settings of the router, the following page "Home / Information" will be displayed, where the device model and firmware version are indicated.

To update the firmware, left-click on its version. The "System / Firmware Update" page opens.

Click the Browse button and select the update file on your computer. Then click "Update". Wait for the router to reboot (1 - 2 minutes).

The file with the firmware update for the DIR 300 N150 router, revision D1 can be found on the official D-Link website or by entering the following URL in the browser address bar.

ftp://ftp.dlink.ru/pub/Router/DIR-300A_D1/Firmware/

The firmware file is named 20140228_1302_DIR_300AE_2.5.4_sdk-master.bin (see the picture above).

The software update must be performed when the router is wired to the computer.

If, after flashing, the router does not work correctly, restore the factory settings of the device. To do this, use the appropriate section of the menu or the hardware RESET button (press with the router turned on and hold for 10 seconds, then release, the router should reboot).

Important! Updating the router firmware is done at your own risk. If the warranty period has not yet expired, then an independent software update (not through a service center) will invalidate it.

First of all, we will consider the general scheme of connecting the router.

As you can see, everything is quite simple, connect a computer / laptop to any LAN port (there are 4 of them) using a network cable (it is included in the kit), insert the provider's network cable into the WAN port, connect the router to a 220V network and press the Power button.

Now I propose to disassemble the indication of the router.

Indicator - Power
Does not burn-Dlink dir300 is off.
Lit-Meals included.

Indicator - WPS
Flashing slowly-Attempting to establish a Wi-Fi connection using the WPS function
Does not burn-The WPS function is not used.

Indicator - Internet

Lit-Connection established
Flashing - WAN interface is active
Does not burn - The network cable is not connected.

Indicator - Wireless Wi-Fi
Does not burn-Wi-Fi is off.

Flashing - Data transfer in progress via Wi-Fi

LAN Ports 1-4 Connecting to network connectors
Does not burn-The cable is not connected to the corresponding connector of the Keenetic, or the network connection is not established.
Lights up or flashes -The network connection is established, information is being transferred.

Next, I propose to go to configuring the router, for this you need to configure on your computer / laptopautomatic retrieval of network settings ... After that, open any browser (IE, Chrome, Yandex, Firefox, Opera) in the address bar, write the IP address of the router 192.168.0.1 ... If you are connecting to the web interface for the first time, you will be prompted to change the login password. I recommend using a complex password - at least 8 characters using letters, numbers and specials. signs.

If you have already connected, enter the login - admin and the password - the one you specified (the default is admin). If the web interface uses a language that does not triple you, click the " Language", and select the required language.

To save the settings, click the " Save". In the future, also do not forget to press the button" Save".

Updating the firmware on the Dlink dir 300 D1 router.

For a more stable and secure operation of the router, the first thing to do is to update the router's firmware, for this, look at what version of the firmware you have installed, this information is in the main window of the web interface.

Then find out the hardware revision (H / W) of your router. To do this, take a look at the sticker on the bottom of the router. This sticker has an inscription that begins with "H / W Ver .:". The following letter and number indicate the hardware revision (in this example, Dlink dir-300 D1).

Then download the latest firmware version according to your revision.

Important!!! DO NOT install firmware other than your hardware revision, this may lead to a complete failure of your device. After that, it will be possible to restore the router only for money by contacting a specialized service center.

After that, on the web interface of the router, click on the version of the installed firmware.

Click the " Overview"specify the path where you have the firmware file (file with expansion .bin). Then press the button " Refresh".

Attention!!! Do not turn off your computer / laptop or router while updating the firmware. This can damage the router and render it unusable.

The firmware update will take about 2-3 minutes, during the update the router will reboot. After downloading the router, you will see the updated firmware version.

Setting up the Internet on Dlink dir-300.

To configure the Internet and Wi-Fi, it is necessary on the web interface of the router in the menu "Net" push the button "Click" n Connect ".

Then make sure you plug the ISP cable into the WAN port and click " Further".

After that, you must specify the type of Internet connection, you can find out this information from the provider's contract or contact those. provider support.

Confirm the specified settings.

In case of successful configuration, you will see a window confirming Internet access. Don't forget to press the " Save".

Setting up a Wi-Fi network on Dlink dir-300 D1

The situation in which you need to do firmware recovery on DIR-300 routers different revisions may arise for different reasons. In addition to the failure of the firmware, when the WiFi router simply stops distributing the Internet and its web interface becomes inaccessible, it can be a simple rollback to the usual "stock" firmware after DD-WRT. Or it can be recovery after an unsuccessful flashing, when the router was fed firmware from a different hardware version.
In general, the developers - the D-Link company - foresaw a similar development of events and on many modern devices they made the Emergency Web Server or Failsafe UI, which is actually the same thing. Now let's figure out how to use it together.

Before doing any actions with the router, you must first download the firmware from the official D-Link server - ftp.dlink.ru:

You can find out which hardware version of DIR-300 you have on the sticker on the back cover of the case:

After that, go to the required folder on the server, look for the "Firmware" directory there and download the latest firmware version and the previous one, just in case. After that, we begin to conjure with a piece of iron. Disconnect the provider's cable and all clients from it, except for the computer from which we will do the recovery.
Then we do this - go to the Local Area Connection settings and manually register the IP address in the TCP / IPv4 properties 192.168.0.2 , mask 255.255.255.0 and the gateway - 192.168.0.1 :

You can register the addresses of DNS servers, or you can not - this is not important, since they will not be involved. Click on OK and close the settings.

We take our DIR-300 in our hands and hold down the button Reset:

Keeping it pressed, turn off the power of the router with the other hand and turn it on again. We wait 15 seconds and release Reset.

Now you need to launch an Internet browser and fill in the address - http://192.168.0.1 in the address bar. The result should be like this:

There may be one more nuance here. Earlier DIR-300 models had an emergency recovery interface at a different address. Therefore, if your router does not respond to 192.168.0.1, then again go to the properties of the TCP / IP protocol and register this kind of ay-pi:

IP: 192.168.20.80
mask: 255.255.255.0

In the address bar of the browser, you also need to enter the address 192.168.20.81:

The interface of the Emergency Web Server and Failsafe UI is actually one to one - the file selection button and the flashing start button. Click on "Browse" and select the downloaded firmware file. Then click on "Upload" and wait for the end of the process.

What do we have as a result? Working D-Link DIR-300 router! All good!