The Windows installer will not install. The message “The installation did not manage to create a new one or find out the existing system partition”, what should I do? It’s easy to capture a video and download an MP3

Hour after hour, during the installation of Windows, the system informs that the installation program was unable to create a new or find a new system partition. This problem does not allow the installation to continue, and leaves many people in a stupor. There are a number of simple ways to figure it out. First of all, it is necessary to understand the root causes of the problem.

What does this pardon mean?

I didn’t get around to creating a new section - how would I go about it?

Let's look at a number of options.

Method 1

The simplest way to do this is to select a hard drive instead of a flash drive as the main storage device. If the power is down, how should I start the installation? In fact, to use a flash drive, there is no need to reconfigure the BIOS. Today's computers allow you to select devices and start them immediately at the right time. To start the computer, press the F8 key. In the window, select a suitable USB device without changing the setup from launching the disks.

Method 2

At the moment of mercy, remove the flash drive. Once the computer is restarted, and after the USB drive is present, the machine imports information from drive C. After this, you can reconnect the flash drive and check for the installation to complete. cesus.

Installing OS from internal storage

If you were unable to solve the problem using the above methods, try another option: Between the hour of installation and the hour of partitioning, create one disk, and then fill in the unallocated area. Format the potential section under the OS. For an additional combination SHIFT+F10, go to the command row:

1. First command: diskpart
2. Following: list disk

Command to display overflow of accumulated people. Ideally, you will have two devices - a hard drive and a USB storage device. Remember the disk number. It is mentally clear that his number is “0”.

1. Enter the command: select disk 0
2. The list of disk partitions is now displayed: list part
3. Remember the partition number you are using for OS installation. Enter the command: select partition 1
4. The value assigned to the disk is "active": active
5. Formatable: format fs=ntfs quick assign exit

We have deprived the Diskpart utility, but we can continue to use it in the command line. Let's go to the root of the flash drive. Acceptable flash drive letter is “D”:

1. Then enter the following command: cd d:
2. Run the command to copy installation files: xcopy d: c: /e /h /k
3. After the process is completed, enter: bootsect /nt60 c:

After this command, drive C becomes beautiful. Now unplug the flash drive and restart your computer. When the desktop starts, press the combination Win + R and enter:

Msconfig

In the window that appears, remove Windows Setup from the “Location” tab. In addition, remove the installer files from drive C. Turn off the power. Show why your difficulties are so that we can help.

setupprep.exe Windows 10 installation program— the preparation process before installing or updating Windows 10. This file is part of the Media Creation Tool. The minimum version of Windows that supports Windows XP with Update 3. After you want to update, you can go to the folder: C:\$Windows. ~ BT \ Sources or on the installation site.

On a Winx64 system, you may have setupprep.exe Windows 10 installation program (32 bits)

Some problems you can address

• The Windows 10 installation program is already running.
• Try another installation disk that contains the %s-bit version. When you insert it into the drive, the Windows 10 installation program will automatically restart.
• It is impossible to know the required XML version
• Transferring data to the crotch and saving it to your hard drive
• The installed programs did not start correctly. Restart your computer and begin installing Windows 10.
• The installation program was unable to launch the traditional server in cooperation with the client
• The installation program could not start Install.exe
• The installation program was unable to connect to the user interface
• The Windows 10 installation program does not support command line arguments. Run the command "setup.exe/?" at the command row at the root catalosis of the installed nose.
• We found that the installation resembles a hemstone process. There could be an interruption of the boundary, which periodically breaks. Repeat installation test
• The selected architecture does not match your computer. For example, if you have a 64-bit version of Windows installed on your computer, you need to install the 64-bit version separately. Try launching the system again and re-entering so that the appropriate architecture is selected.
• Just before I started the program, a problem occurred. Close the account, restart the computer, and then try to start the account again.
• We need at least 350 MB of space to run the installed program. Change the disk space and try again.

Having recently decided to reinstall Windows, just before the installation time, when the process proceeded to select the local disk on which to install the operating system, Windows received the following error: The installation program was not able to create a new or sign go to the original system partition. This error message appears when you try to install the Windows 7 operating system. When you try to install Windows 8 or Windows 8.1, you receive the error “We were unable to create a new or find the new partition.” I am aware of both insults and mercy, and I will boldly say that there is a stench, however. I will also provide information that I know on the Internet: this warning in Windows Vista sounds like this: “Windows cannot find the system volume that is suitable for installation.” All these apologies are expressed in one way only in what is written, so let’s get to the top, and before that I will describe the symptoms of this illness. In addition to this, you can note that the system update partition is not created (in some operating systems this partition is divided. So, up to Windows 7, this partition takes up 100 MB, and in Windows 8 and higher - 350 MB.)

Why didn’t you manage to create a new one or find out the existing system partition?

In an attempt to get rid of this problem, a number of actions were carried out, which I would like to teach you:

• Replacing Windows distribution. Create a new one, and then create a new distribution.
• Formatting and selecting all partitions on the hard drive. Disk formatting is as simple as possible, as there is no important data. After deleting sections of the trace, try a number of options:
  • Install Windows on the unzipped area.
  • Create one section and try to install it.
  • Create 4 parts and try on one of them. The main information is that if 4 or more sections are created, the system update section will not be created and the installation can be completed successfully.
  • Create one partition and try to install Windows in an unmarked area.
• You can try to do the same thing through the command line for help. To select the command row, press Shift+F10.
• In the BIOS, switch the SATA mode from IDE to ACHI, or vice versa.
• Try resetting the BIOS settings to default settings.
• Connect all other flash cards or other USB devices from your computer.
• In the BIOS, set the hard disk drive to the first place, and the hard drive to the other place. If there is already an operating system on the hard drive (for example, if you want to create additional storage), then during storage, use the F10 or F12 keys to access the storage menu, where you can select your flash card or CD drive. Since the hard drive does not have an installed OS, the system will automatically select your distribution.
• I also remember that the flash card must be inserted into the computer only after the computer is turned on (in my opinion, this is the case).
• If you have a number of physical disks, turn off all but one.

In most cases, the options described above will help and the system will need to be installed. If these steps did not help you and you still see the message “I couldn’t create a new one or find the existing system partition,” read further.

Installing Windows from a hard drive

I think no one is bothered by the information that Windows can be used from a flash card or from a CD (DVD) disc. All these options are supported by the fact that the operating system image is located on an external device (flash card, CD-ROM or throat server). Now we will try to install Windows in a more complex and very different way. When installing, the Windows image will be on the hardest disk where you are going to deploy the image! To succeed in this scam, follow my instructions:

1. Take advantage of the original installation disk (by all means, you already have it).
2. Reach the window for adjusting hard drives, where we spent our time.
3. Break the hard disk so that you are tempted. If there is no important information on the disk, it is best to create one partition for the system, and leave the area that is missing as unmarked. The partition for the system needs to be formatted.
4. After this, press the keys Shift+F10 (or Alt+F10) to open the command row window.
5. In the command row window, enter the command:

   Here is a list of all available disks.

6. For everything, there will be two disks listed - your hard disk and a flash card. Next to your hard drive will be the number that you need to enter in the attack command. Shvidshe for everything, tse number 0.

   When you press this command, a list of available sections will appear. Since you have created only one division for my pleasure, then you yourself will be rewarded. If not, then search for the partition where you want to install Windows and remember its number.

7. Finding the partition number, enter the following command:

   select partition 1

8. The following sections are active:

   active

9. Formatable:

   format fs=ntfs quick

assign

We exit from the Diskpart utility, but do not exit from the command row window.

10. Using the offensive command, we go to the root of our flash card (CD disk):

    cd d:

    UPDATE: In order for this moment to pass without any difficulties and the advisers to stop complaining about possible concessions in the comments, I would like to clarify that the letter D: the letter D of your flash drive may appear be some other letter of the Latin alphabet. To understand this, you need to enter the commands sequentially in the command line window

    diskpart

    list volume

    This command will display a list of all logical sections on your computer and the corresponding names of the letter, among which you must know your flash drive, make sure to remember the memory of the flash card letter and in For further commands, replace this entry with d:. To get the drive letter without putting it into our main documents, it will be easier if you open another window of the command row, for which read point 4 again.

11. Let's enter the command:

    xcopy d: c: /e /h /k

    which copies all installation files from the flash card to drive C:. Make sure your copy is complete.

12. Let's enter the command:

    bootsect /nt60 s:

    This adds a special encryption code to the C drive, making it difficult for the hard drive to run Windows.

13. At this point, the creation of the mechanical hard disk is completed. Now you can change the flash card and restart your computer. When the time comes, the computer will begin installing Windows directly from the hard drive. Once the operating system is installed and a desktop appears in front of you, select these actions.
14. Press Win+R and select the program

    msconfig

    In the window, go to the Privacy tab and select Windows Setup.

15. Open the disk:. Now it is necessary to clean the disk of installation files that we do not need. You can take the list of files and folders that need to be deleted from your installation flash drive.
16. I see, you ran into a problem.

The axis is so foldable, but if you do not use it in this way, you may be forced to remove it. The installation program was unable to create a new or find the existing system partition. Good luck to you!

At the right time, the warning “The installation program failed to create a new or identify the original system partition” did not really get on my nerves, but fortunately now I know the reason and a number of ways to bypass it or correct it, which I am sharing with you.

The message “The installation program was unable to create a new or find the existing system partition” can also be seen when installing Windows 7 or installing Windows 10, the error looks something like this:

When choosing a partition on your hard drive, you can create, format or delete it, and when you select a partition to install and press the “Next” button, a message will be displayed about the impossibility of installing Windows on this disk. Most often, and most often, this problem occurs when installing Windows from a USB flash drive.

Reasons for the error “The installation program was unable to create a new or find the existing system partition”:

• In the BIOS of a computer or laptop, the first device on the list of storage installations is not the hard drive, but any other device - DVD, flash drive, storage device, etc.
• The computer has more than one hard drive or SSD installed, the unnecessary one can be plugged in for an hour of Windows installation
• Incorrect settings for settings in BIOS
• The flash drive with which Windows is installed is not suitable for this, it is recommended to convert the encrypted flash drive with another program and create another image of Windows that is as original as possible.

The most common reason for this pardon, first. Starting from Windows 7, the installer checks the BIOS settings and does not work correctly, since the installer believes that your instructions for installing Windows do not put the hard drive first on the list of devices to install, so it will not continue. and installation and a notification appears: “The installation program could not be created new or know the existing system partition.

To correct this problem, you can do the following:

1. Go to the BIOS and set up a list of devices to configure so that the hard drive is the first one in the future. For some BIOS, select a special Fixed Boot Order item - which fixes the order of your instructions and does not allow them to change. In some older BIOSes, it is not possible to adjust the order of devices, or rather, you can, except when connecting a flash drive, such a BIOS for any reason must be installed on the hard drive. If the order of downloading has been adjusted, then to download from a flash drive, use the Boot-Menu, which can be accessed using the F8-F12 keys at the top of Esc, F1 or F2, and then the Windows installation will proceed in normal mode.

2. Another reliable way to resolve the problem is to partition the hard drive and copy the installation files to a new one, make it a new one and re-install it, in which case you will install Windows where it is launched directly from the hard drive and runs in normal mode without problems. To do this, you need to start the installation and in the installer create one partition on your hard disk, which will be drive C, then press Shift+F10, a command row may open, in which you need to enter a number of commands:

diskpart- start the utility

list disk- show a list of available disks, the list at least requires one hard drive and a flash drive for storage, regardless of the size, it doesn’t matter which disk you need to select, remember its number, to select the disk with which you will need to enter the command:

select disk 0(select disk 0, if your hard disk has a different number, indicate it)

list part A list of partitions on the disk is displayed, in the installer you are responsible for creating one partition, remember its number and indicate to the next command, for example, we need partition number 1:

select partition 1

active- make sure that this section is active, so that it will be victorious at the time of attraction

Now we can no longer format our system partition, for which we enter the commands:

format fs=ntfs quick

assign letter=C(C is the drive letter you want to assign to the partition, if you are busy, you can choose another one, remember, we will need it at the file copying stage)

exit- Exit the disrpart utility and continue running in the command line.

We need to identify the flash drive assigned to the letter in order to copy files from the flash drive to the created and formatted partition on the hard drive. To search for the memory of a flash drive, you can type the command cd e: or just e: Where - it is possible that the letters of a flash drive, sometimes the letters are assigned not from the beginning of the alphabet to the end, try if the disk with the letter you selected does not work and you remove the notification about the cancellation, if the disk with such a letter є the team will be vikonana, in which type vikonovate the team DIR Here you will see a list of folders and files - with them you can see which drive letter belongs to. Once the letter assigned to the flash drive has been found, you can begin copying files.

For example, the letter of the flash drive is E, the letter of the hard drive partition is Z, then the command for copying files looks like this:

xcopy E: Z: /e /h /k

When copying ends, exit the command:

bootsect /nt60 s:(de z is the letter of the partition on the hard drive, don’t get confused)

The last command is to install the drive from the hard drive, after which you can remove the flash drive, adjust the BIOS to the drive from the hard drive and restart the computer, if everything is installed correctly, then the Windows installation may start and proceed normally without any problems From selecting a section or disk for installation.

After completing the installation process, you can delete the application entries from the installation menu and the msconfig command, as well as delete the installation files from the hard drive, which will no longer be necessary.

I hope this report will help you find the reasons and correct the error: “We were not able to create a new one or find out the existing system partition.”

Most of the problems that happen during the Windows installation process are completely typical, but they are narrowed down to the middle ones and are completely unforeseen, which can put a well-informed customer in a dark place. You begin installation, and even before the start of copying the files, the process interrupts, and the master sees a failure “I didn’t manage to find out the license agreement. Make sure the installation option is entered correctly and restart the installation.".

This rare error may crash when Windows is installed either on a virtual machine or on "zalizo".

Trying to start the installation again will not lead to anything, the problem is repeated immediately. There may be a number of reasons for this strange problem, including licensing that has nothing to do with it. When Windows is installed on the hypervisor Hyper-V The program may fail if the virtual machine does not have enough RAM.

For normal work Windows 8.1і 10 on a virtual or entirely real computer there may be at least 1 GB RAM, in another case, the installation will end with a BSOD otherwise, what gets spoiled a lot more often, with mercy. As an alternative, if the disk is already damaged, right before the installation begins, you can try creating a swap file on the system partition. To do this, press Shift+F10 in the installer window and enter the command wpeutil createpagefile /path=D:\pf.sys .

When installing the system on "zalizo" A better solution can be described if the Windows distribution has been damaged. Open the checklist of the corrupted image, if you avoid the original, rewrite it on your computer, or even better, proceed with another installation procedure or disk. If the installation is inconsistent with the optical nose, reverse the fit DVD-The disk in the drive is not turned on, so it was not rotated quite correctly, so the laser was not able to process some of the data.

If you find that the error may be due to the mismatch of the version and system key specified in the product identifier file pid.thxt. The problem seems to be this way. Create a text file in Notepad and paste it into two rows:

OEM

Save file as ei.cfg then put it in the catalog sources on a flash drive, anyway ISO-image, add the file to the creation distribution kit, repackaging the image for additional help Ultra ISO or a similar program.